How to Remove and also Replace a Bath Tub.
How to Remove and also Replace a Bath Tub.
Blog Article
They are making a few great pointers regarding Installing A Bathtub overall in this great article in the next paragraphs.
Installing a bath tub isn't specifically rocket science, yet it does call for strong plumbing, woodworking, and also often, tiling abilities. Changing an old tub with a brand-new one is additionally a reasonably tough job. If the old bathtub is easily easily accessible, the project can move quickly; if you have to open a wall surface to get rid of the old bathtub as well as position the new bathtub, the job is a lot harder. In either instance, the job is within a house handyman's skills, although you will require an assistant to leave the old tub and set in the brand-new one. See to it you have qualified yourself for the work and also are comfortable attempting it. Rather than working with a service provider to take control of a halfway-completed job, it is better to consider utilizing one before you start. Opportunities are you may need a specialist plumber to make tube links.
This post will aid you set up a new bathtub in your washroom if you have already acquired a new tub and also don't need to alter the arrangement of your previous water system pipes.
Your devices and product checklist need to make up the following:
Planning for the Installation
To start with, the supporting framework supplied with the bath needs to be fitted (if needed) according to the supplier's guidelines. Next, fit the faucets or mixer to the bath tub. When fitting the tap block, it is very important to make sure that if the tap features a plastic washer, it is fitted in between the bathroom and the faucets. On a plastic bathroom, it is additionally practical to fit a sustaining plate under the taps system to prevent stress on the bath tub.
Fit the flexible tap adapters to the bottom of the two faucets using 2 nuts and olives (often provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the outlet via the hole in the bathroom. Use the nut supplied by the supplier to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the versatile overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bathroom. See to it you use all of the supplied washing machines.
Attach the trap to the bottom of the waste outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Connect the bottom of the overflow tube in a similar manner.The bath must currently be ready to be fitted in its last placement.
Removing Old Taps
If you need to change old faucets with new ones as a part of your setup, after that the first thing you must do is separate the water. After doing so, turn on the taps to drain any water staying in the system. The process of eliminating the existing faucets can be rather bothersome as a result of the limited accessibility that is often the case.
Use a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that connects the supply pipes to the taps. Have a cloth ready for the remaining water that will certainly originate from the pipelines. As soon as the supply pipelines have actually been gotten rid of, utilize the exact same tool to loosen the nut that holds the taps onto the bath/basin. You will need to stop the solitary faucets from transforming throughout this procedure. When the taps have been removed, the holes in the bath/basin will have to be cleansed of any kind of old securing substance.
Before moving on to fit the brand-new faucets, contrast the pipeline links on the old faucets to the brand-new faucets. If the old faucets are longer than the brand-new taps, then a shank adapter is required for the new faucets to fit.
Mounting the Tub
Utilizing the two wooden boards under its feet, position the bath tub in the needed setting. The wooden boards are helpful in equally spreading out the weight of the bath tub over the location of the boards as opposed to concentrating all the weight onto 4 little points.
The next goal is to ensure that the bathtub is leveled all round. This can be attained by examining the level as well as changing the feet on the bathtub until the level reviews degree.
To set up taps, fit the bottom of the outermost adaptable faucet port to the suitable supply pipe by making a compression sign up with; then do the same for the various other tap.
Switch on the water as well as check all joints and also new pipework for leaks and also tighten them if required. Fill the tub and additionally examine the overflow electrical outlet as well as the normal electrical outlet for leaks.
Ultimately, repair the bathroom paneling as explained in the manufacturer's user's manual. Tiling and securing around the tub should wait till the bathtub has actually been utilized at the very least once as this will certainly settle it right into its final placement.
Fitting New Touches
If the tails of the new faucets are plastic, then you will certainly need a plastic adapter to avoid damages to the thread. One end of the adapter fits on the plastic tail of the tap and also the other end supplies a connection to the existing supply pipes.
If you require to fit a monobloc, after that you will call for decreasing couplers, which attaches the 10mm pipe of the monobloc to the common 15mm supply pipe.
Next off, place the tap in the placing hole in the bath/basin making sure that the washing machines are in area between the faucet and the sink. Protect the faucet in place with the maker provided backnut. When the faucet is securely in place, the supply pipelines can be connected to the tails of the taps. The faucets can either be connected by using corrugated copper piping or with regular tap ports. The previous kind ought to be linked to the faucet ends first, tightening up only by hand. The supply pipes can later on be attached to the other end. Tighten both ends with a spanner after both ends have actually been attached.
Tiling Around the Bathtub
In the area where the bathroom fulfills the tile, it is required to secure the accompanies a silicone rubber caulking. This is important as the fitting can move sufficient to fracture a rigid seal, triggering the water to permeate the wall surface in between the bathroom and the tiling, resulting in issues with wetness and also possible leaks to the ceiling below.
You can select from a range of coloured sealers to assimilate your fixtures and fittings. They are offered in tubes as well as cartridges, and also can securing voids approximately a width of 3mm (1/8 inch). If you have a larger gap to fill up, you can fill it with twists of drenched paper or soft rope. Bear in mind to constantly load the bath tub with water prior to securing, to permit the movement experienced when the tub is in use. The sealant can crack fairly early if you do not consider this motion prior to securing.
Additionally, ceramic coving or quadrant ceramic tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are likewise quickly offered on the market. It is recommended to fit the tiles using water-resistant or water-proof glue and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I'm just very inquisitive about How to Install a Bathtub Yourself and I'm hoping you liked the entire blog post. Sharing is nice. You never know, you may very well be helping someone out. Thanks for taking the time to read it.
Check It Out Report this page